Car companies are relying more and more on flash reprogramming to correct driveability and emissions related problems in newer vehicles. This procedure is usually done at a new car dealership, but with the right software and tools independent repair shops or even individuals can reprogram their PCM Powertrain Control Modules (PCMs) and other onboard electronics. Basic steps of flash reprogramming a vehicle computer. U.S. Environmental Protection Agency regulations require original equipment manufacturers to make emissions-related onboard diagnostic service information available to the aftermarket via their technical websites, including updates on reprogramming vehicle modules. The flash reprogramming procedures must conform to SAE J-2534-1 standards, which allow the use of aftermarket scan tools or similar pass-through devices in addition to the factory scan tool. EPA rules require auto makers to post all of their text-based service and training information on the internet so anyone can access it, and at reasonable cost. For a complete listing of these websites and fees, Click Here. MOST LATE MODEL VEHICLES CAN BE FLASH REPROGRAMMED Most domestic vehicles built since 1996 (over 150 million!) have computers that can be reprogrammed (for a listing of vehicles that can be flash reprogrammed, Click Here). Reprogramming may be required for a variety of reasons. One is when a vehicle sets false trouble codes. The original factory programing may be overly sensitive or not take into account wear or other factors that may affect the operation of certain sensors or the OBD II monitors. CLICK HERE for a list of General Motors modules that are reprogrammable on 1993 to 2008 model year vehicles (pdf file). PCM Reprogramming is also necessary to change the engine idle speed, spark timing, fuel mixture or other emission control functions. PCM Reprogramming may be required to resolve a hot or cold starting issue, idle roughness, stalling, or an emissions failure. Reprogramming is often used to modify the operation of emission functions so they have less of an effect on drivability. PCM Reprogramming may be necessary to smooth out or change the shift characteristics of an automatic transmission. It may also be used to modify the operation of the ABS, traction control or stability control systems, to change steering feel on vehicles with variable assist steering, and to change the ride characteristics on vehicles with electronic ride control. If a PCM, TCM, BCM or other control module is being replaced on a vehicle, reprogramming may be required to calibrate the new module to that particular vehicle (unless it has been preflashed by the OEM or module supplier). Also, additional learning procedures may be required to "initialize" the module so it will function properly. One thing reprogramming cannot do is fix mechanical problems like vacuum leaks, dirty fuel injectors, worn spark plugs, piston rings or bearings. If an engine or other component has a mechanical problem, these need to be diagnosed and ruled out or repaired before reprogramming is considered as a repair possibility. PERFORMANCE REPROGRAMMING A PCM Reprogramming is also a trick that many tuners use to enhance engine performance and dial-in more horsepower. Reprogramming can change spark timing, fuel enrichment and boost pressure (on turbocharged and supercharged engines) to make more power. Reprogramming is usually required after installing an aftermarket performance cam, bigger cylinder heads, a different intake manifold or fuel induction system to compensate for changes in airflow. Many performance chips on the market claim to remap engine timing by altering sensor readings sent to the ECU, but a professional tune is still highly recommended for these chips as well, when used in conjunction with other aftermarket parts. Reprogramming can also change the shift points of the transmission, disable the factory built-in rev limiter and vehicle speed limiter, and recalibrate the ABS/traction control system for different sized aftermarket tires and wheels. This type of reprogramming, however, requires a special aftermarket tuner scan tool, as well as software that is not provided (or approved) by the vehicle manufacturer. HOW A PCM STORES PROGRAMMING INFORMATION Before Onboard Diagnostics II arrived in 1996, the calibration instructions for most PCMs and other modules were located on "Program Read Only Memory" (PROM) chips. These integrated circuit chips were plugged into the module main circuit board, and could only be programmed once. If the instructions needed to be changed or updated for any reason, the PROM chip had to be physically removed from the module and replaced with a newer version. This created a proliferation of OEM PROM part numbers, as well as a lot of confusion about which PROM was the "right" one for a particular application, as well as which PROM was the latest version. For performance tuning, the original PROM chip could be replaced with an aftermarket performance PROM chip that provided more spark advance and fuel enrichment under certain driving conditions. But on vehicles that lacked a PROM chip, this was not possible. Caution: PROM chip can be easily damaged by mishandling. Static electricity can zap the chip's memory, and the little prongs that plugged into the circuit board can be easily bent or broken. If you are replacing a PROM chip, you should wear an anti-static wrist ground strap and take precautions to minimize the risk of a static discharge. In the early 1990s, General Motors began to use a new type of memory chip called an EPROM (Erasable Program Read Only Memory). This chip had a little window on it that allowed the chip to be reprogrammed with new instructions when it was exposed to a bright ultraviolet (UV) lamp. As the technology continued to evolve, the next improvement was the EEPROM (Electronically Erasable Program Read Only Memory) chip. These started to appear on OBD II cars in 1996, and soon became common because EEPROM chips could be electronically reprogrammed without having to remove the chip or expose it to an ultraviolet lamp. It could be reprogrammed by applying a higher than normal voltage. This told the chip to accept new instructions so new information could overwrite the old information on the chip. The latest version of this technology is the Flash EEPROM, which is essentially a higher capacity EEPROM chip that can hold more information (typically 512 megabytes or more) and can be overwritten more quickly and easily. TOOLS REQUIRED TO REPROGRAM PCM To reprogram a PCM or other vehicle module, you need a factory scan tool, or an aftermarket scan tool with reprogramming capabilities, or a J-2534 compliant "PassThru" interface tool (or J-2534-1 for 2004 & newer vehicles) that can connect a PC or scan tool to the vehicle's diagnostic connector or module. The updated software for reprogramming the vehicle comes from the vehicle manufacturer. The software may be downloaded from their website (which requires a broadband, DSL or faster connection, not a simple dial-up connection), or it may be supplied via CD or DVD after paying their subscription fee. With few exceptions, the software is NOT free. A subscription fee or access fee must be paid to obtain the software. And to install it, you need a scan tool with reprogramming capability, or a J-2534 or J-2534-1 PassThru tool. For a list of subscription fees and OEM technical websites for accessing this information, see Listing of OEM websites and fees. THere are also aftermarket odometer recalibration tools that can be used to reset the odometer reading on the instrument cluster, PCM and BCM. The legality of these tools is questionable because some people (used car dealers primarily) are using these tools to roll back the chilometroage on used cars. Turning back the odometer tens of thousands of chilometri can increase the resale value of a used car thousands of dollars. So there is an incentive for the used car dealers to cheat consumers using these tools. Anodometer reset tools typically sels online for around $300 and plugs into the diagnostic connector under the steering column like other scan tools. You need a J2534 compliant scan tool to reprogram a PCM or other module. HOW TO REPROGRAM A PCM OR OTHER MODULE The first step is to determine whether or not any updates are available for a particular vehicle, and if so whether or not such an update might be needed to solve a particular problem. Updates can be found by searching recent TSBs or recalls. This will tell you which makes/models/years (or VINs or module part numbers) are covered by an update, and what symptom, problem or issue the update is designed to resolve. NOTE: Even though an update may be available for a vehicle, it does NOT mean the vehicle must be updated. As long as the vehicle is running fine and is experiencing no problems, there is no need to update it. On the other hand, if the vehicle has a problem that may be resolved by installing an update, then updating would be a good idea. The next step is to use a scan tool to determine which version of software is currently loaded in the vehicle. If it is not the latest version, and the vehicle is having a problem (or would benefit from an upgrade), reprogramming would be the next step. After downloading or obtaining the latest software from the OEM, the information must be transferred to a scan tool or J-2534 PassThru device that is plugged into the vehicle diagnostic connector. Modules can also be bench reprogrammed off the vehicle by connecting the scan tool or PassThru tool directly to the module, but it is usually easier to reprogram it on the vehicle. Caution: During the reprogramming procedure, power to the module and reprogramming tool must not be interrupted. A charger should be attached to the battery to make sure there is a steady supply of voltage during the procedure. Also, the scan tool or J-2534 PassThru tool must not be disconnected until after the in…

Fonte: AA1Car.com