When ABS was first introduced back in the mid-1980s, it was strictly a braking system for preventing wheel lockup and skidding. Then traction control was added as the technology evolved to prevent wheel spin during acceleration. Then came an advancement that would take ABS to an entirely new level. Electronic Stability Control (ESC) allows ABS systems to automatically brake individual wheels as needed to improve handling and steering control under all driving conditions. Electronic stability control essentially makes ABS a full-time expert back seat driver that's constantly monitoring how the vehicle is responding to the driver and road conditions. If a problem starts to develop, it springs into action and takes whatever measures are necessary to get things back under control. This includes reducing engine power by backing off the throttle and/or retarding spark timing, and simultaneously applying one or more brakes to counter the forces that are causing the vehicle to lose control and/or traction. The neat thing is that all this happens automatically without any driver input! HOW ELECTRONIC STABILITY CONTROL WORKS To better control vehicle dynamics under all driving conditions, the ABS system needs some additional inputs. This includes a steering angle sensor to monitor the driver's steering inputs, a yaw sensor to detect changes in vehicle momentum that might cause the vehicle to spin out, oversteer or understeer, and a lateral acceleration (g-force) sensor to monitor changes in deceleration. When the driver steers the vehicle, the steering angle sensor keeps the ABS control module informed about where the driver is aiming the vehicle and the rate at which the steering wheel is being turned (fast or slow). At the same time, the ABS control module looks at the inputs from its wheel speed sensors to determine if there are any differences in the rotational speeds of the right and left front and rear wheels. Turning a corner causes the inside wheel to rotate at a somewhat slower rate than the outside wheel. If a vehicle begins to oversteer in a turn and the rear end starts to come around (which would cause the car to spin out), the speed difference between the left and right front wheels increases. If the vehicle understeers (loses front traction and goes wider in a turn), the speed difference between the left and right front wheels decreases. If the stability control software in the ABS control module detects a difference in the normal rotational speeds between the left and right wheels when turning, it immediately reduces engine power and applies counter braking at individual wheels as needed until steering control and vehicle stability are regained. Click Here to download/view a video clip of a Chevy Tahoe rollover test. In this clip, which was taken at the Bosch proving grounds in Flat Rock, Michigan, the driver makes a sharp swerve at 35 mph with the stability control system disengaged. The SUV goes up up on two wheels and nearly rolls over. The test is then repeated with stability control engaged and the vehicle remains flat on the ground. LEAVE STABILITY CONTROL ON OR TURN IT OFF? Most vehicles have a switch or button that allows you to turn off stability control. So should you leave it on or turn it off? The factory default setting for stability control is always on. For normal driving, leaving stability control on will usually provide the best handling and safest braking in most situations, especially for less experienced drivers. Some SUVs that may be used off-road offer a range of stability control settings that reduce wheel spin and improve traction on slick surfaces such as mud, ice or snow. Refer to your owners manual for which settings are recommended for certain types of driving. Stability control will also enhance performance driving on a track, allowing you to handle sharper turns with less understeer or oversteer. It will also reduce wheel spin when accelerating hard. But you obviously can't do burn outs off the line at a drag strip with traction control on, or go drifting around a corner if the system is trying to prevent wheel spin. So in these situations, an experienced driver would want to switch stability control off temporarily to gain more control over the vehicle. STABILITY CONTROL APPLICATIONS The first vehicles to come factory-equipped with electronic stability control were the 1995 BMW 750iL and 850Ci models with a 5.4 liter V12 engine. The Bosch-built Dynamic Stability Control (DCS) system monitors individual wheel speeds 50 times per second (every 20 milliseconds), and is always active whether the driver is braking or not. If the system senses an understeer or oversteer condition developing, it takes one of two courses of action depending on the amount of cornering force or lateral acceleration that's being developed. If the vehicle's lateral acceleration is greater than about 0.6g,and the driver brakes normally (not hard enough to bring antilock braking into action), the DSC system modulates brake pressure so that the outside wheels are braked more than the inside wheels. This counteracts the oversteer or yaw effect that might otherwise cause the vehicle to lose control and spin out. If the driver realizes he's going too fast and hits the brakes hard enough to kick in the normal antilock braking, DSC reverts to a normal ABS braking mode allowing the system to selectively modulate rear brake pressure as needed. MERCEDES ESP STABILITY CONTROL An even more sophisticated Electronic Stability Program (ESP) appeared in 1996 on V-12 powered Mercedes S600 models. Like BMW system, the Vehicle Dynamics Control (VDC) system is also made by Bosch and provides automatic engine torque reduction and braking if a car enters a corner too fast or makes a sudden steering maneuver. But unlike the BMW system, Mercedes also uses individual front and rear braking to help the vehicle regain control. With the Mercedes ESP system, the front brakes may be applied separately to help correct the vehicle's attitude. If the car is going into a left turn, for example, and is starting to oversteer, the ESP system applies the right front brake to help bring it back under control. To correct an understeer condition when cornering left, the ESP system applies the left rear brake. A dash warning light also flashes to alert the driver that the stability control system is active (a glowing triangle with an exclamation mark inside). The Mercedes system takes inputs from two additional sensors: a lateral acceleration sensor and a yaw velocity sensor. The latter tells the control module if the car is turning on its axis so the computer can compare the input to the steering angle and speeds of the individual wheels. CADILLAC STABILITRAK In 1997, Cadillac added Delphi's new StabiliTrak stability control system to its Seville STS, DeVille Concours and Eldorado ETC models. The StabiliTrak system compares what the driver wants to do with how the car is actually responding. If the car isn't responding the way the driver wants, or is in danger of spinning or skidding out of control, StabiliTrak slows and stabilizes the car to help the driver regain control. Like the BMW and Mercedes stability control systems, Cadillac also uses a steering angle sensor, yaw sensor and lateral acceleration (g-force) sensor. LEXUS VEHICLE STABILITY CONTROL In 1998, Lexus added the Bosch Vehicle Stability Control (VSC) system to some of its cars. Operationally, it is the same as the Mercedes and Cadillac systems, but adds a brake pressure sensor to monitor driver braking inputs (or lack thereof), and a warning buzzer in addition to the dash light to warn the driver when the system is active. STABILITY CONTROL SYSTEMS Stability control has been integrated into virtually all vehicles today, including cars, SUVs, light trucks even heavy-duty trucks. It is especially beneficial on SUVs because of their higher center of gravity and increased risk of roll-over if they get sideways or spin-out on a slick road or suffer a tire blowout. In 2006, stability control was available on about a third of new cars and trucks, including 57% of all SUVs. By 2010 it was used on 85 percent of all new vehicles. And by 2012 it became standard equipment on all new cars, SUVs and light trucks. Stability Control System Names Stability control systems are offered under the following names: * Acura: Vehicle Stability Assist (VSA) * Alfa Romeo: Vehicle Dynamic Control (VDC) * Audi: ESP – Electronic Stabilization Program * Buick: StabiliTrak * BMW: Dynamic Stability Control (DSC), including Dynamic Traction Control * Cadillac: All-Speed Traction Control & StabiliTrak * Chevrolet: StabiliTrak (except Corvette – Active Handling) * Chrysler: Electronic Stability Program (ESP) * Dodge: Electronic Stability Program (ESP) * DaimlerChrysler: Electronic Stability Program (ESP) * Fiat: Electronic Stability Program (ESP) and Vehicle Dynamic Control (VDC) * Ferrari: Controllo Stabilita (CST) * Ford: AdvanceTrac and Interactive Vehicle Dynamics (IVD) * GM: StabiliTrak * Hyundai: Electronic Stability Program * Honda: Electronic Stability Control (ESC) and Vehicle Stability Assist (VSA) and Electronic Stability Program (ESP) * Holden: Electronic Stability Program (ESP) * Infiniti: Vehicle Dynamic Control (VDC) * Jaguar: Dynamic Stability Control (DSC) * Jeep: Electronic Stability Program (ESP) * Kia: Electronic Stability Program (ESP) * Land Rover: Dynamic Stability Control (DSC) * Lexus: Vehicle Dynamics Integrated Management (VDIM) with Vehicle Stability Control (VSC) and Traction Control (TRAC) systems * Lincoln: AdvanceTrak * Maserati: Maserati Stability Program (MSP) * Mazda: Dynamic Stability Control * Mercedes: Electronic Stability Program (ESP) * Mercury: AdvanceTrak * MINI Cooper: Dynamic Stability Control * Mitsubishi: Active Skid and Traction Control MULTIMODE * Nissan: Vehicle Dynamic Control (VDC) * Oldsmobile: Precision Control System (PCS) * Opel: Electronic Stability Program …

Fonte: AA1Car.com