Wheel balancing is a must anytime tires are mounted on wheels. The wheel may also require rebalancing if a tire has been dismounted for repair. Wheel balancing provides a smoother ride by minimizing tire vibration and bounce. This helps improve traction, steering control and extends the life of your tires. But no matter how carefully wheels and tires are balanced, they will eventually lose their balance. As the tread wears, the distribution of weight around the circumference of a tire changes altering the balance of the tire and wheel assembly. Eventually the tire may have to be rebalanced because only 1/4 ounce of imbalance can produce a noticeable vibration. WHEEL BALANCE PROBLEMS An out-of-balance tire and wheel will typically create a vibration or shake that become progressively worse as the vehicle's speed increases. The speed at which the vibration first becomes apparent will vary depending on the size and weight of the tires and wheels, the size and weight of the vehicle, the sensitivity of the steering and suspension, and the amount of imbalance. The vibration or shake usually starts in at 40 to 50 mph and increases in intensity as the speed increases. A tire/wheel imbalance will typically be felt as a shaking or vibration in the steering wheel. If the vibration is bad enough, the car itself may shake violently! Should you be worried about a tire/wheel vibration? Probably not because it does not normally create a dangerous situation. It won't damage your vehicle, but it can be very annoying and distracting while you are driving. A tire imbalance problem will also cause your tires to wear unevenly (cupping wear) which will eventually ruin the tires. So don't put off having your tires inspected and rebalanced. It could save you the cost of having to replace your tires prematurely. Although most tire balance problems are the result of normal tire wear, a tire may go out-of-balance if a clamp-on or stick on balance weight comes loose and falls off. Speed-related tire and suspension vibrations may also be caused by radial (vertical) or lateral (sideways) runout in a tire, wheel or hub. A bent wheel (from hitting a pothole or curb) will wobble and vibrate at speed, causing a vibration. Other causes of tire/wheel-related vibrations include loose, worn or damaged wheel bearings as well as uneven tread wear caused by misalignment or worn suspension components such as tie rod ends and control arm bushings. Loose or broken lug nuts may also allow a wheel to wobble (very dangerous!) and vibrate. HOW TO CHECK WHEEL BALANCE If you have a vibration problem or your steering wheel shakes at highway speeds, take your vehicle to a tire dealer or repair shop so they can inspect your tires and wheels, and check the balance of your tires. They should also inspect the steering and suspension for any other problems that might be causing a vibration or shake. If the problem turns out to be the tires, rebalancing them should eliminate the vibration. Most tire dealers charge around $15 to $20 per wheel to rebalance your tires. If you are buying new tires, free balancing may be included as part of the package price. Some tire stores also offer free lifetime rebalancing when you buy a new set of tires. WHEEL BALANCER To accurately balance tires and wheels, a tire dealer or repair shop must have an up-to-date and accurately calibrated wheel balancer. This type of equipment should be capable of achieving both static (at rest) and dynamic (in motion) balance. Old fashioned bubble wheel balancers can do a decent job of achieving static balance, but dynamic wheel balance can only be achieved with a spin balancer. This is especially important with today's larger, wider, heavier tire and rim packages, and absolutely essential for run-flat tires that have thicker, stiffer sidewalls. Most wheel balancers today have self-calibrating electronics with accuracy to hundredth's of an ounce (or tenths of a gram). Graphical displays also make information easier to read and understand, and reduce the chance of making a mistake. Automatic data entry for wheel width and diameter on some balancers also saves time. Installing tire balance correction weights – courtesy Hunter Engineering. When a tire and wheel assembly is spun on a tire balancer, it does not spin as fast as the tire would turn when driving on the highway. This reduces the danger to the tire technician while reducing strain on the balancer and the time it takes to complete the balancingh process. Older balancers typically had to spin a wheel fairly fast (about 500 rpm, or the equivalent of 55 to 60 mph) to generate a usable signal. But the more sensitive electronics in today's wheel balancers are able to pick up vibrations at much lower speeds (only 100 rpm, or 10 to 15 mph). As the tire and wheel spin on the balancer, the machine detects the amplitude and location of any vibrations caused by static and/or dynamic imbalance. The machine then calculates how much correction is needed and shows the tire technician where exactly to place the correction weights. WHEEL BALANCING TECHNIQUES One of the limitations of balancing tire and wheel assemblies off a vehicle is that repeatability can be an issue. In other words, the machine may not show the same results when an attempt is made to rebalance a wheel that has already been balanced. This can happen if the wheel is not remounted on the machine correctly. The way that a wheel is mounted on a balancer will not only affect the accuracy of the balance job itself but also the repeatability of the balancing results. Worn mounting cones or shaft bearings are sometimes the problem. Using the wrong type of cone can also give inaccurate results. So too can dirt on the wheel or nicks in the wheel center hole. But another often overlooked cause is using the wrong mounting technique for the type of wheel. The basic idea is to mount the wheel on the balancer the same way it is mounted on the vehicle. A pilot hole centric wheel (one where the center hole positions the wheel on the hub and prevents it from wobbling sideways when the lug nuts are removed) can be mounted on a balancer with a cone from the backside. But a lug centric wheel (one that does have some sideways movement when the lug nuts are removed) requires a different balancer mounting procedure. A lug centric wheel should be mounted with a cone from the backside and an adapter flange plate against the front side. The fingers on the flange plate must be properly positioned so they line up with the lug holes in the wheel. This is necessary to center the wheel on the WHEEL balancer shaft. If this is not done, the results will not be 100 percent accurate or repeatable. WHEEL & TIRE RUNOUT VIBRATIONS Sometime wheels will still shake and vibrate even after they have been carefully balanced. The problem is often excessive wheel runout or tire runout. Most tires should have less than .030 to .050 inch of runout (or less depending on the application). An out-of-round tire can produce harmonic vibrations that come and go at various speeds depending on how many "humps" are in the tire. As a rule, most steel rims should have less than .050 inch of runout, or .040 inch of runout if the rims are aluminum alloy. Some trucks and SUVs can tolerate up to .060 inch of radial and lateral runout, but others can't handle any more than .030 inch of runout before vibrations become noticeable. Runout problems can often be corrected by "match mounting" the tire on the wheel (rotating the tire so the tire high spot is over the rim low spot). With brand new tires, the tire installer should line up the RED or YELLOW colored dot on the tire sidewall with the tire stem to reduce runout and imbalance. With existing tires, a dial indicator is required to find the high and low spots on the tire and wheel. The tire can then be rotated on the wheel to line up the tire high spot with the wheel low spot to reduce overall total runout. If this fails to reduce runout enough to eliminate the vibration, you will have to replace the tire or wheel that is out-of-round. Note: Some tire shops have tire truing machines that can shave rubber off portions of the tread to make an out-of-round tire rounder. Some places may also have wheel straighting equipment that can restore a slightly bent rim. RADIAL FORCE VARIATION Sometimes the problem is neither balance or runout. It is radial force variation (RFV). This is the amount of change in stiffness of the sidewall and footprint when a load is placed against a tire. Subtle differences in the position of the cords and belts in a tire's construction can create stiff spots that make the tire roll unevenly. The stiff spots act like runout to cause vibrations at various speeds. Low profile tires (those with aspect ratios of 50 or less) are typically much more sensitive to force variations due to their stiffer sidewalls. Vibrations caused by RFV tend to appear at certain speeds, then disappear as the speed changes or increases (unlike vibrations caused by imbalance that usually get worse as the speed increases). In one test, a perfectly round wheel that was properly balanced experienced a vibration that appeared at around 50 mph but vanished at 70 mph. The vibration at 50 mph was caused by RFV in the tire, and produced as much side force as if the tire were out-of-round by .030 inches or out of balance by one and a half ounces. Some high end tire balancers have a large roller that can be placed against the tire to detect runout when the tire is rotating under load. If RFV is present, it shows the technician where it is and how to correct it. RFV can be countered by adding offsetting weights and/or rotating the tire on the rim. It also makes it easier to determine if a tire is responsible for a vibration problem or not. If there is no runout problem, no RFV and the tire is accurately balanced, but the car still vibrates, the vibration is in the driveline or powertrain, not the wheels and tires. Check th…

Fonte: AA1Car.com