Tire wear is a dead giveaway that the wheels are out of alignment or that steering or suspension parts are worn. So anytime you find unusual tire wear, be sure to give the steering and suspension a thorough inspection to find out what's causing the problem. Different Types of Tire Wear: The following are different types of wear that can develop on your tires. It's important to visually inspect your tires periodically for wear because wear can affect safety, handling and braking. Some types of wear may also indicate worn or damaged steering or suspension parts that need to be repaired. Toe wear Toe refers to the parallelism of the wheels to each other. Toe misalignment typically produces a feathered wear pattern across both front tires, and/or inner shoulder wear on both tires (see the photo at the top of the page for an example of extreme toe wear). Front toe wear occurs when the front wheels bow out (too much toe out) as the vehicle is traveling forward. The underlying cause is often worn tie rod ends, but can also be caused by worn or loose inner tie rod sockets on rack and pinion steering gears, worn or deformed control arm bushings, a bent tie rod, bent steering arm or even misalignment in the rear wheels (which throws the steering off-center while driving straight). Measuring toe out with the wheels turned 20 degrees to either side can help you detect a bent steering arm. If toe wear is accompanied by steering looseness or steering wander, there's a very good chance the tie rod ends are worn. Proceed to the steering checks. If toe wear is accompanied by steering pull or off-center steering, rear wheel toe alignment or axle alignment may be out of specifications. Toe wear on the inside edges of the REAR tires on a vehicle with an independent rear suspension can also result from toe misalignment (too much toe out). The underlying cause may be rear rod alignment adjustments out of specifications, worn or damaged rear suspension control arm bushings, rear control arm bushings that have too much compliance (give) and allow too much lateral movement of the rear control arms, a bent rear control arm, or worn rear ball joints. Severe tread wear caused by misalignment. Camber wear Uneven wear on one side of a tire tread may occur when the tire is leaning due to camber misalignment. The underlying cause may be bad control arm bushings, loose ball joints, a bent spindle or strut, or a strut tower that s out of its normal position (due to factory misassembly, collision damage, body sag or severe corrosion). Another overlooked cause of camber wear can be a front-wheel drive engine cradle that has shifted out-of-position to one side. A weak or broken spring can also allow camber changes in the suspension that produce camber wear on a tire. Cupped wear This may be the result of badly worn shocks or struts, or wheel and tire imbalance. Diagonal wear Uneven wear that occurs at an angle across the tread or along the edge of the tread on the REAR tires of a FWD car, minivan or SUV with an independent rear suspension. This type of tire wear can be caused by rear toe misalignment, worn rear control arm bushings, excessive flexing of the rear suspension or not rotating the tires often enough (every 6000 to 7500 chilometri is recommended). A slight variation is heel-and-toe wear that occurs along the inside edge of the tread. Heel-and-toe wear is caused by unwanted toe and camber changes that occur while driving. The uneven tread wear produced by diagonal wear or heel-and-toe wear makes the surface of the tire rough, which may produce a rumbling or humming noise while driving that sounds like a bad wheel bearing. You can usually feel the undulations and roughness on the tread by rubbing your hand around the circumference of the tire. Tire wear chart Measuring Tire Wear Tires have wear bars (flat spots)in the tread grooves to visually indicate wear. If the tread is worn down so the wear bars are flush with the surrounding tread, the tire is worn out and needs to be replaced. If you see cords showing through the rubber, the tire is unsafe to drive on and is on the verge of failure. Replace the tire without delay! The same advice goes for any tire that has bulges, deep cracks or the tread is separating from the casing. Tread wear can be measured using a penny. Place the penny with Lincoln's head upside down in a groove between the treads. If you can't see the top of Lincoln's lead, the tire is okay and still has some wear left in it. But if the top of Lincoln's head is flush with the tread, the tread depth is 2/32-inch (1.6mm) or less, indicating the tire is worn out and needs to be replaced. Some experts now say the same test should now be done with a quarter. If the top of Washington's head is flush with the tread when you place a quarter upside down in a groove, the tread depth is 4/32-inch (3.2mm). Though the tire still has some tread wear left, braking, traction and handling are significantly reduced on wet pavement compared to a tire with more tread on it. Because of this, many experts now recommend replacing tires when the tread depth is worn down to 4/32-inch or less if you drive in an area that receives a lot of rain or snow. Tire tread wear can be measured with a simple gauge like this. Tread depth should be checked in the middle of the tread, and in about one inch from each side of the tread. Tread depth should also be measured at several different locations around the circumference of the tire to check for flat spots. Causes of Tire Wear: Toe or Camber Misalignment The tires have to roll straight and true, be perpendicular to the road surface (camber) and be parallel to each other (toe) to minimize tread wear. If the wheels are out of alignment, tread wear will increase. Toe misalignment has the greatest effect on tread wear, while camber misalignment causes wear on the inside or outside edge of the tread. If your tires are wearing unevenly or rapidly, you should have the alignment of all four wheels checked. If toe or camber are out of specifications, the wheels need to be realigned back to factory specifications. This should always be done if you are buying a new set of tires. Worn Tie Rod Ends The most common cause of rapid tread wear on the front tires is toe misalignment due to worn tie rod ends in the steering linkage. A bent tie rod or steering arm can also change toe alignment, but in most cases the problem is the tie rod ends are worn out and have too much play. As a rule, inner and outer tie rod ends should show no visible vertical or horizontal play when rocking the steering back and forth with the full weight of the vehicle on its wheels. If you see any movement in the joint, the tie rod end needs to be replaced. The inner tie rod sockets on rack and pinion steering gears are enclosed in bellows, making them more difficult to inspect. If the bellows are rubber, you can check for looseness by squeezing the bellows and pinching each socket while pushing outward on the wheel or while a helper rocks the steering wheel. If you feel movement, the sockets are loose and need to be replaced. You can't do this check with hard plastic bellows, so lock the steering wheel with a holder and watch for any in or out movement in the tie rod while pulling and pushing on the wheels. Also pay attention to the rack mounts. Loose, deteriorated or broken mounts may allow the rack housing to move as the wheels are steered. This can cause steering wander and noise. With parallelogram steering systems, pay close attention to the amount of play in the idler arm. Looseness here can cause steering wander and toe wear. Pitman arms should show no vertical looseness. Center links should be like tie rod ends and show no vertical or horizontal play. How to Check Your Steering The steering can be inspected using a technique called the "dry park" check. With the full weight of the vehicle on the wheels, have a helper rock the steering wheel while you look for play or looseness in the steering linkage and steering column. On some vehicles, this can be done by reaching up and rocking the steering column coupling from underneath while the vehicle is sitting on ramps or a drive-on ramp-style lift. The dry park method of checking for looseness is generally the best procedure to use because the weight of the vehicle on the wheels creates resistance that makes it easier to see play. The dry park method is also a good way to find loose upper strut bearing assemblies. While rocking the steering back and forth, watch for strut movement in the strut tower opening. Any wobble would tell you the strut bearing plate is worn and needs to be replaced. While rocking the wheel back and forth, also watch the control arm bushings for excessive movement. You can also check the bearings by gently prying against the control arm to see if the bushings allow much movement. A little "give" with rubber and elastomer bushings is normal, but if you see more than about 1/8 inch it may mean the bushing has collapsed. Metal bushings should have little or no play. Bouncing the suspension can help you identify noisy bushings. Underinflated Tires If the tires are not maintained at the recommended pressure and are underinflated, the tread flexes more than usual as the tire rotates. Over many chilometri, this will increase tread wear. Check the pressure in each tire with an accurate gauge, and inflate the tires to the pressure recommended in your owners manual or the inflation decal in the glovebox or door pillar. Sagging Springs or Bent Suspension Parts Weak, sagging springs can cause a los of ride height that throws off wheel alignment. Coil and leaf springs sag with age, which can alter camber as well as caster alignment. Measuring ride height will tell you if the springs are still within specifications or not. If ride height is below specifications, the springs need to be shimmed or replaced. If ride height is okay but camber is out of specifications and a tire shows heavy shoulder w…

Fonte: AA1Car.com